Exhaust Products
BurnSim lists a solid rocket motor's exhaust products - every species, by mass, for the whole burn - both at the nozzle exit and fully burned in air. It works them out from the propellant's ingredient recipe with the same equilibrium chemistry it uses for C* and flame temperature, and puts them on the Results Tab and a second page of the motor report.
Commercial license only. On personal, educational and trial licenses a motor with a recipe propellant shows one line, Exhaust products: available with a commercial license. See the purchase page.
What it answers
How much hydrogen chloride does this motor put out? How much alumina? How much carbon monoxide leaves the nozzle, and how much air does it take to burn it off? These are questions about the motor, not the propellant: the answer depends on how much propellant is loaded, the chamber pressure it burns at and the nozzle it expands through. BurnSim answers them in pounds (or metric units) for the motor you have designed.
Typical uses:
- Test sites and test cells. The acid gas and particulate from a static firing, for an enclosed or semi-enclosed stand, a range's rules, or a neighbor's question.
- Paperwork. A per-motor emission figure, with the assumptions written next to it, for a permit application, a safety review or a customer.
- Comparing formulations. Swap the oxidizer or the metal and see what moves: the chlorine from ammonium perchlorate, the condensed oxide from aluminum, the carbonate from potassium nitrate.
The two blocks
Both blocks are listed largest first, with condensed (solid or liquid) species marked, and anything below the listing cut lumped as other (trace).
At the nozzle exit is the equilibrium composition of the recipe at the burn's time-weighted average chamber pressure, expanded to the motor's own nozzle expansion ratio (1 for a bare throat). This is the exhaust as it leaves the nozzle, before any of it burns in the air. Fuel-rich propellants leave a lot of CO and H2 here.
Fully burned in air is the other limit: every bit of CO and H2 oxidized to CO2 and water by bookkeeping, with metal oxides and salts carried through unchanged. Its total weighs more than the propellant, because it includes the oxygen taken from the air, and the block says how much oxygen that is and roughly how much air it comes with. The air's own nitrogen is not listed. No NOx is estimated.
Neither block is a plume prediction. How much afterburning a real plume does depends on its temperature and how fast it mixes with air, which BurnSim does not model. The real exhaust lies somewhere between the two blocks, which is why both are given.
Worked examples
Both motors below are the same hardware: two 1.5 in x 3 in BATES grains with 0.5 in cores, about 0.60 lb of propellant, a 0.30 in throat and a 0.75 in exit (expansion ratio 6.25). The text is what the Results tab shows, less each block's trace line and caveat.
KNSB (65% potassium nitrate, 35% sorbitol), 500 psi average
Exhaust products at nozzle exit, by mass (500 psi avg chamber, expansion ratio 6.25): K2CO3(b) (condensed) 0.268 lb 44.4% CO2 0.128 lb 21.2% H2O 0.088 lb 14.5% CO 0.059 lb 9.8% N2 0.054 lb 9.0% H2 0.007 lb 1.1% Fully burned in air (the limit: all CO and H2 oxidized), by mass: K2CO3(b) (condensed) 0.268 lb 38.9% CO2 0.221 lb 32.0% H2O 0.146 lb 21.2% N2 0.054 lb 7.9% Takes 0.086 lb of oxygen from the air (about 0.371 lb of air); the air's nitrogen is not listed.
Nearly half of a sugar motor's exhaust by mass is potassium carbonate - the white smoke. No acid gas at all.
AP/Al/HTPB composite (70% ammonium perchlorate, 16% aluminum, 12.5% HTPB, 1.5% IPDI), 800 psi average
Exhaust products at nozzle exit, by mass (800 psi avg chamber, expansion ratio 6.25): AL2O3(a) (condensed) 0.182 lb 30.2% CO 0.152 lb 25.2% HCL 0.130 lb 21.5% H2O 0.053 lb 8.9% N2 0.051 lb 8.5% CO2 0.019 lb 3.1% H2 0.014 lb 2.3% CL 0.001 lb 0.2% Fully burned in air (the limit: all CO and H2 oxidized), by mass: CO2 0.258 lb 32.3% AL2O3(a) (condensed) 0.182 lb 22.8% H2O 0.177 lb 22.1% HCL 0.131 lb 16.4% N2 0.051 lb 6.4% Takes 0.196 lb of oxygen from the air (about 0.848 lb of air); the air's nitrogen is not listed.
About a fifth of an ammonium perchlorate motor's exhaust is hydrogen chloride, and with 16% aluminum nearly a third is alumina particulate. A quarter is carbon monoxide at the nozzle exit, which is gone in the fully burned limit.
Where it appears
- Results tab - both blocks, at the bottom of the tab, after the run.
- Motor Report - a second page with both blocks as tables, each with a total row; page 1 says the page is there.
- Ingredients window - for the propellant rather than a motor: a chamber and nozzle-exit table of mole and mass fractions, condensed species starred. Other licenses see the chamber mole fractions only.
Neither block is in the CSV export or batch mode output, which are time series.
What it needs
- A propellant with a thermochemistry recipe - the list of ingredients and their mass fractions. A propellant with hand-entered C*, gamma and molar mass has no chemistry to work from. In a motor that mixes the two, the recipe propellants are listed and the others are named as not included.
- A commercial license.
What it leaves out
- Anything that is not propellant. Nozzle erosion, liner, inhibitor and igniter products are not included.
- Afterburning, except as the fully burned limit. No plume temperature or mixing model.
- NOx. Not estimated in either block.
- Kinetics. The exit composition is equilibrium at the exit. Real nozzles can freeze some of the chemistry before the exit; equilibrium is the standard first answer and the one tools like ProPEP and CEA give by default.
See also
- Propellant Thermochemistry - the recipe, and how C*, gamma and flame temperature come from it
- Ignition Transient - the other commercial-only output